KPM Auto > Ford > New Performance Products

FORD V8 5.4 OIL SEPARATOR & BREATHER KIT

Reduce oil consumption and Detonation!

This is an essential component that can reduce or eliminate oil consumption & intake charge contamination through the intake system. If you've removed your intake plenum and noticed oil build-up, then you may need an Oil Breather Separator to absorb the oil and prevent its passage into the intake system.

Herrod Motorsport recommends the use of an Oil Breather Separator for all supercharged and high performance naturally aspirated applications. It is especially beneficial for vehicles used for track day events where vehicles run wide open throttle for extended periods of time.

The Twin CNC Machined Billet Aluminium Oil Breather Separators utilise an inline PCV valve and a new grommet for the right hand rocker cover & the left breather connects to the factory valve cover breather hose that feeds into the air inlet tube/throttle body assembly.

The billet component is assembled with a lower and upper housing, two screens and an oil vapour/mist filter media. The housing threads together utilising a rubber seal. This facilitates inspection of the filter media. The filter media is sandwiched between two mesh screens, which allow the oil vapour/mist to be absorbed and collected by the filter and then passed back through the lower screen.

The price for the street kit is $335.00. Allow $25.00 for fitting.

The price for the off road kit is $380.00. Allow $55.00 for fitting.

KF30 KPM Engine Piping Kits

KPM are now stockists and dealers for Plazmaman Racing Components.

With the aftermarket performance upgrades generating greater power, Ford standard inlet hoses were unable to meet these increases in pressure. Therefore, we introduced the Plazmaman kits on our top end performance upgrades. KPM also searched for cheaper alternatives for lower range upgrades and found Plazmaman products to be of comparable quality and finish. We have currently been using them on various vehicles with great results.

Power increases using the Plazmaman Racing Components have been easily achieved by fitting a basic engine piping kit. We have consistently been able to tune an extra 20 kilowatts by just replacing the engine piping alone.

Our Engine Piping basic kit sells for $1200 supplied, including fitting, tune check and minor reset on dyno.

Ask us for a quote to have a custom tune installed to compliment your engine piping upgrade kit.

Other products include intercoolers and full engine piping kits.

KPM Blueprint Injectors

KPM Motorsport have been high flowing and blue printing injectors now for 9 years on all makes and models. We have been blue printing the Ford range injectors (Bosch EV6) since they were released, all with great results.

Our injectors are blueprinted to flow within 2% variation of each other and are fully tested for correct pattern, leak down and atomisation.
All injectors are then ultrasonically bathed and fully re-kitted before final testing and sale.

New injector variations are usually within 4% and we believe after our high flowing process, our 2% variation is more suited to the high performance engines which demand more exact fuelling. Prices listed below :

New Bosch 0 280 155 968 44lbs $98
KPM Blueprint 44lbs $70ea
KPM Blueprint 49lbs $70 ea
KPM Blueprint 54lbs $70 ea
KPM Blueprint 59lbs $70 ea

All KPM Blueprint injectors are on a change-over basis.
$40 extra per injector if no change-over is available.

Bosch EV6 injectors are the correct injectors for the Ford and Holden range of vehicles and give more precise fuelling due to the breakpoints being calibrated exactly by the factory computers. This means correct fuelling at all load points and rev ranges without the computer trying to fight the injector while in closed loop.

Customised tuning to these injectors becomes easier and less expensive due to precise tuning being achieved much quicker.

Larger EV6 injectors can be purchased on special order.

KF19 KPM Ripshifter Stockists

KPM are now stockists of the Ripshift 5 and 6 speed gear stick assemblies for BF/BA model Fords and earlier. If you haven’t felt the difference with these gear sticks, come in and we would be happy provide you with a demonstration. You’ll never miss third gear again with straight gate selection.

Ripshift Gear Stick Assembly $499
KF19 Ripshift Gear Stick Assembly Fitted $795

Performance Fuel System

KPM Motorsport have designed, tested and released a new fuel system for the BA-BF V8 , Turbo and 6cyl range of utes and sedans.

After years of fitting the in tank Walbro unit and having many issues regarding , noise, vibration and intank hoses not being suitable for high octane fuels and octane boosters we decided to engineer a 100% race/ road system that works.

Advantages:

Assembly fully self-contained
Utilises Premium Bosch Motorsport High Volume Fuel Pump
Save money and easily mount yourself with minimal tools
All fittings and hoses supplied
All fittings clip into original Ford fuel lines.
No cutting or modifications.
Proper swirl pot arrangement
Purpose built for High Performance road/All motosport applications.
Twin pump unit available.
Utilises genuine in tank pump as lift pump.
All quality manufacturing, fittings and componenets only.
Single pump unit flows for up to 600 hp.applications
Twin pump unit available for 600 hp plus applications

Price

Complete assembly including Fuel Pump $1495
Complete assembly excluding Fuel Pump $1195

Fitting extra
Interstate freight extra

New Ford Performance Products